Liquid Cooling Suggestions for a Face Lift

[Man]

It's just a joint connecting two tubes Rakesh.
One color tube goes into a hollow piece covering it half & the remaining half of the hollow piece is taken by the other color tube. that simple no mounting business.
& they will pass through the space provided at the sides only.

[mav2000]

Remember that in water cooling simple is the way to go. For each new fitting point, there is an additional area where leaks can start. And the plastic fittins dont do a great job, which is why you barely see people using them. Man, take my advice, try and keep it as simple as possible first. Then add funky stuff as you keep learning.

[rakesh_sharma23]

I thought you were planning joints like this

[Man]

Guys I'm looking for a red LED or RED uv 120mm fan, with high flow( >55 cfm) , high pressure (>1.5mm H2O), low noise (<30db)
The only thing I could find is the Coolermaster 90 CFM Red LED Silent Fan 120mm (R4-L2R-20CK-GP) at an amazing price of Rs.450

[rakesh_sharma23]

No low noise Fan.. only UV here

Apevia 120mm 4pin UV Red LED Case Fan at Xoxide!

A.C. Ryan BlackFire4 UV LED Fan - 120mm (RED Outside, RED Inside)*at*ArcticMOD.com

[Man]

Going to order the rest of the stuff now.
Am I missing some thing?

[Man]

How would a 140mm blue led fan look over the CPU?

[rakesh_sharma23]

So you want to replace two 80mm Fans on top panel with 140 mm ones...

[mav2000]

There is the new CM red fan as well. Its a copy of the blademaster but with red blades and LED's. Much much better than the R4.

[Man]

No, the 80mm fans will remain. I will rotate the top plate by 180' & make a new cut for the 140mm fan.
The only problem I see on the face of it that the two 80mm fans will not allow the tall water blocks to be installed in the last two pci-x slots.
Other cards pose no problems. What I am more worried about is the look. Cos even the transparent fan will hinder vision of the CPU block.

---------- Post added at 10:59 AM ---------- Previous post was at 10:52 AM ----------

Originally Posted by mav2000 There is the new CM red fan as well. Its a copy of the blademaster but with red blades and LED's. Much much better than the R4.

Where can one see or buy one of these?
Is the blade master better than the R4 ?

[rakesh_sharma23]

Yes true Fans over the GPU will hide the water block.... Better make a new top with one 140mm fan over CPU and VRM heat sinks...

[mav2000]

Yup Blade master is a whole lot better.

[Man]

Originally Posted by rakesh_sharma23 Yes true Fans over the GPU will hide the water block.... Better make a new top with one 140mm fan over CPU and VRM heat sinks...

I can afford to use the other 2 pci-x slot (the motherboard has 4 I can use for the GPU's) just the last two have problems.
I was thinking of using the last two so that a 90' rotatory compression fitting for the water pipe going down straight out will make it look cleaner than the gradual turning (refer to my picks posted )

Originally Posted by rakesh_sharma23 Better make a new top with one 140mm fan over CPU and VRM heat sinks...

So, you think a 140mm fan will not pose hindrance in the CPU view ?
In that case need suggestions for a new chrome 140mm fan grill.
Designs only limited to your imagination(will have them laser cut)
Restrictions:-
Has to be 2D, should pose little resistance to air flow & work well with the 80mm fan grill installed. (refer picks)

[Man]

What!! nothing comming to mind?

---------- Post added at 04:02 PM ---------- Previous post was at 04:01 PM ----------

Originally Posted by mav2000 Yup Blade master is a whole lot better.

On paper it does'nt

[Man]

Originally Posted by mav2000 There is the new CM red fan as well. Its a copy of the blademaster but with red blades and LED's. Much much better than the R4.

where can I find me one of these?